Free 3D print files

Nordlys Print Files

Printable growing gear, made for a 256 × 256 mm bed (Bambu Lab P2S).

Ventilation

Window mounts and duct supports

Clip-on Window Sealing Panel · Draft

A removable sheet panel for an approximately 450 × 1,200 mm window opening, with a continuous edge seal and printed duct fittings. Rotate the preview to inspect the panel, padded push-on clips and hose connector. The sheet is cut separately.

Download free files

  • Adjustable design

    OpenSCAD source: panel, flange, backing ring and push-on clips; confirm dimensions before exporting parts

  • Assembly and measuring guide

    Fit checks, provisional dimensions and assembly instructions

  • Assembly preview

    Illustrative 3D model; not a printable model or cutting template

Opening width
≈450 mm
Opening height
≈1,200 mm
Status
Draft

Print settings

  • The large panel is purchased sheet material. Only the fittings are intended for printing on the P2S.
  • Measure the hose connection and update the CAD first: the preview uses an unconfirmed 150 mm hose and 8 mm sheet.
  • Starting point for fittings: ASA, 0.20 mm layers, 5 walls and 40% infill. Use suitable ventilation and the filament manufacturer’s profile.
  • Export individual fittings from OpenSCAD after confirming their dimensions. Print one fit sample before the full set; no ready-to-print STL is included in this draft.

How to use

  1. Check the opening at several points and make a cardboard template. Confirm clearance around hinges and the open sash.
  2. Choose a continuous sealing surface on the fixed frame. The illustrated 15 mm overlap is provisional, not a sheet cutting dimension.
  3. Fit a continuous EPDM gasket. Padded C-clips slide over the panel edge and an accessible fixed-frame lip, with no drilling into the window. Confirm the rear lip is reachable and the clips clear seals and hinges.
  4. Gasket the duct flange, fit its backing ring and support the hose separately. Keep window drainage paths clear.
Concept preview, not a verified fit. Opening dimensions are approximate; hose diameter, sheet thickness and frame lip dimensions still need confirmation. The illustrated 30 mm frame depth is a placeholder; clip grip has not been physically tested. Do not cut the sheet or print the full set from the example dimensions.

160 mm Window Duct Holder · Screw-free V6

The pressure shoe, wedge and pin sit 40 mm farther along the jaws to reach past the rear gap. Both jaws extend to keep the padded contact faces aligned. This screw-free version prints as one flat main piece, with the three smaller parts nested inside the duct ring on a single P2S plate.

Download free files

  • P2S PLA plate — all 4 parts

    Bambu Studio project: 0.4 mm nozzle, 0.20 mm layers, supports; fit prototype

  • Plate geometry

    Same four-part layout; apply your own material and support settings

  • Clamp fit test

    Optional smaller test; also print the shoe, wedge and pin

  • Holder and 160 mm duct guide

    One flat piece; two outer corners relieved to fit the 256 mm P2S bed

  • Pressure shoe

    40 mm offset along the jaw, with the same snug fit; add a 2 mm soft pad

  • Wedge with indoor grip

    Extended handle and lanyard hole; seven locking positions

  • Printed locking pin

    Retains the wedge; secure and inspect its friction fit

Nominal duct
160 mm
Guide bore
164 mm
Shoe offset
40 mm

Print settings

  • Open the P2S PLA 3MF as a project in Bambu Studio. It contains the holder, wedge, shoe and pin on one plate. Keep the flat arrangement and use print-by-layer; do not use sequential printing or increase the brim width.
  • Configured for a 0.4 mm nozzle and textured PEI plate: Generic PLA, 0.20 mm layers, 6 walls, 6 top/bottom layers, 50% gyroid infill, automatic supports and a 1.5 mm outer brim. Confirm the selected filament matches your spool.
  • Remove supports from the wedge rail, shoe tabs, guide grooves and pin holes. Test the mechanism on a clear bench. PLA parts have not been physically tested for flex, creep or holding strength.
  • Supply two soft 40 × 40 × 2 mm pads, a duct strap and an independent short holder restraint. No metal fasteners are needed. V3 screw-based parts are not used.

How to use

  1. Slide the shoe tabs into the jaw grooves from the frame side. Insert the wedge from above into its T guide. Add one 2 mm soft pad to each contact face.
  2. Position the adjustment jaw opposite the duct ring toward the room. The extended wedge grip and locking pin must be reachable indoors; verify access on your actual window.
  3. With the pin removed, press the wedge gently until snug and insert the pin into the aligned hole. The nominal padded gaps range from 59.2 to 64.6 mm. The middle position is 62.8 mm, 0.3 mm tighter than V2.
  4. Retain the wedge and pin with short lanyards and secure the duct without crushing it. The guide ring alone does not stop a vertical duct sliding.
  5. Before any installation above equipment, arrange independent duct support and a short restraint around the whole holder from a suitable indoor anchor. A printed eye alone is not an independent safety support. Keep the window stationary; remove in wind or rain.
PLA fit prototype: the longer jaws and relieved corners have no validated holding strength. Use the clamp test to check rear clearance before installation above equipment. Digital checks cover geometry, seven adjustment positions and plate layout, not grip, strength or long-term creep. Confirm indoor access and independent support before installation.

Adjustable Window Duct Holder · V2

A screw-free clamp with a guided wedge, sliding padded shoe and removable printed locking pin. Designed around your 63 mm window frame, supporting a 100 mm duct upright outside the open window. Test the clamp mechanism before printing the full holder.

Download free files

  • Test clamp — start here

    Full guide and lock mechanism without the duct ring; also print the three moving parts

  • Clamp and upright duct ring

    Final body with guided jaw, 108 mm bore and tether hole

  • Guided pressure shoe

    Tabs keep the padded face aligned; add a soft 2 mm pad

  • T-track wedge

    Captured sideways in the jaw; seven indexed locking positions

  • Removable locking pin

    Split friction pin blocks wedge withdrawal; check fit before use

Nominal frame gaps
59.5–64.9 mm
Duct bore
108 mm
Lock positions
7

Print settings

  • Print the test clamp, shoe, wedge and pin first. Once fit and movement are satisfactory, print the main body and transfer the moving parts. V1 parts are not compatible.
  • PETG starting settings: 0.20 mm layers, 5 walls, 6 top/bottom layers, 40% infill; 100% for the small pin. Keep supplied STL orientations. All parts fit individually on a 256 mm bed.
  • Use local supports beneath the wedge T rail and shoe tabs as needed. Inspect the body’s short slot roofs, pin hole and strap-window bridges in the slicer. Remove support scars from sliding surfaces.
  • Supply two 40 × 40 × 2 mm soft closed-cell foam pads, a 15 mm reusable duct strap and an independent safety tether. No screws, nuts or wedge-retaining strap.
  • The ZIP includes individual and assembled STEP files, the editable generator, full instructions and geometry results. No tested slicer profile or load rating is available.

How to use

  1. Slide the shoe tabs into the jaw grooves from the frame side. Feed the wedge down from above, with its T rail in the jaw track. Add one soft pad to the shoe and one to the fixed jaw.
  2. With the window open and secured against movement, slide the clamp over an accessible vertical sash edge. It reaches 60 mm onto the face. Keep both pads clear of glass, seals and locking hardware.
  3. With the pin removed, press the wedge down gently until snug. Align a hole and insert the printed pin from outside the jaw. It must stay seated without force; never use it to lever the wedge down.
  4. The seven frame gaps are 64.9, 64.0, 63.1, 62.2, 61.3, 60.4 and 59.5 mm with uncompressed 2 mm pads. For your 63 mm frame, 62.2 mm needs 0.8 mm total pad compression. Stop if this needs force; pad thickness and print tolerances affect fit.
  5. Before installing outside, attach an independent safety tether. Pass the duct through the ring with its outlet up and secure it gently using the strap windows. Support the remaining duct indoors.
  6. Check grip and pin retention indoors, then recheck after an hour and daily. To release, support the holder, pull out the pin and lift the wedge. Keep the window stationary while fitted; remove in rain or wind.
V2 prototype: digital checks cover all seven positions and frame clearance, not physical grip or durability. Soft pads and a snug locking pin are essential. Rear frame access remains unverified; the upward outlet is not rainproof. Ordinary room-air exhaust only, with an independent safety tether.

Seedlings

Pots and trays for starting plants

Split Seedling Pots

Two-part starter pots that open sideways, so you can lift out a rooted soil plug without pushing or pulling on the stem.

Buy it printed

Printed to order in Spain
  • 6 split pots

    6 × halves A + B and collars, PLA

    €24.90

  • Seedling starter set

    6 split pots + drip tray

    €34.90

Prices include 21% VAT. Ships in 3–5 working days.

Shipping from €4.95 in Spain · €12.95 to the EU · €24.95 worldwide

Download free files

  • Six-pot print plate

    18 parts, ready to open in Bambu Studio

  • Pot half A

    With engraved Nordlys logo

  • Pot half B

    With engraved Nordlys logo

  • Retaining collar

    Holds the halves together

Rim
55 mm
Height
65 mm
Soil
≈ 96 ml

Print settings

  • The six-pot plate is 237 × 177 mm.
  • 0.4 mm nozzle, 0.20 mm layers, 4 walls, 5 bottom layers, 15% infill.
  • Print by layer, not by object — the parts are too close for sequential printing.
  • Keep the supplied orientation. No supports needed; use at most a 2 mm brim.
  • PLA works indoors. PETG lasts longer with repeated use. Keep PLA away from hot water and direct sun.

How to use

  1. Join halves A and B using the locating tabs at the bottom.
  2. Slide the collar up from underneath. It supports the pot but doesn't lock, so hold both when lifting.
  3. To transplant, hold the halves closed and slide the collar off downward.
  4. Lay the pot on its side and lift away one half, then the other, while supporting the root plug.
Print one set (A, B and a collar) first to check the fit on your printer before printing all six.

Drip Tray for Six Split Pots

Holds six split pots and catches the runoff, including water that spills over the rims. The pots stand on pads above the water, so the soil doesn't sit wet.

Buy it printed

Printed to order in Spain
  • Drip tray

    Tray only, leak-tested, PLA

    €16.90

  • Seedling starter set

    6 split pots + drip tray

    €34.90

Prices include 21% VAT. Ships in 3–5 working days.

Shipping from €4.95 in Spain · €12.95 to the EU · €24.95 worldwide

Download free files

  • Drip tray

    3 × 2 grid with corner guides for each pot

Size
188 × 127 mm
Holds
≈ 194 ml
Print
~3 h

Print settings

  • 0.4 mm nozzle, 0.20 mm layers, 5 walls, 6 bottom layers, 15% infill. No supports.
  • About 3 h 10 m and 158 g of PLA. Leak-test it in the sink first.
  • Fits the larger split pots (55 mm rim) only.

How to use

  1. Stand each assembled pot (halves + collar) between its four corner guides.
  2. Water from the top. Runoff collects below the pads, under the pots.
  3. Empty the tray before the water reaches the pads (about 194 ml), so the soil doesn't stay soaked.
  4. To transplant, lift a pot straight up and split it open as usual.
Not physically printed yet. Check that a pot drops in and lifts out easily before relying on it.

Watering

Keeping the root zone moist while you are away

Wick Reservoir for 11 L Fabric Bags

A self-watering base: the bag stands on a slotted plate above a water tank, and wicks under the bag pull water up into the soil.

Buy it printed

Printed to order in Spain
  • Wick reservoir set

    Tank, lid, float gauge and funnel, leak-tested. Wicks not included.

    €69.90

Prices include 21% VAT. Ships in 5–7 working days.

Shipping from €7.95 in Spain · €24.95 to the EU · €44.95 worldwide

Download free files

  • Reservoir base

    Sealed tank with support pillars

  • Bag plate (lid)

    Drain slots, wick channels, fill holes and gauge guide

  • Small parts plate

    Level float, level rod and fill funnel

Size
244 × 156 mm
Water
≈ 6.6 L
Bag
11 L / 25 cm

Print settings

  • Base: PLA works indoors; PETG is tougher. Use a dark colour to limit algae. 5 walls, 6 bottom layers, 15% infill — about 12 h and 780 g of PLA.
  • Whole set: about 17½ h and 1 kg of filament, so load a second spool in the AMS.
  • Leak-test the base in the sink before using it.
  • Lid: 25% infill, 4 walls, flat side down — it carries the wet bag (~12 kg).
  • Float: upright, no ironing. The hollow inside must stay sealed so it floats.
  • Rod and funnel: as exported, no supports. Push the rod into the float socket.

How to use

  1. Fill the tank through a corner hole using the funnel, then fit the lid.
  2. Lay two wet wicks (~50 cm each) in the crossing channels, ends down through the holes to the tank floor.
  3. Stand the bag on top and water it from above once, so the soil is fully wet and the wicks start pulling.
  4. Refill when the gauge drops. The rod notches mark 2–6 L; don't fill past the top notch.
Wicks: cotton pulls water fastest but rots within a season or two; nylon wick rope lasts longer. Many shoelaces are polyester and wick poorly — test one in a glass of water first. Not physically tested yet.

Feeding

Measuring nutrients accurately

Nutrient Dosing Rack

Holds three nutrient bottles with a labelled syringe holder for each, so every product has its own syringe. A printed part cannot be a measuring cup, so the accuracy comes from the syringes. Use the calculator to work out each dose. Prototype: measure your bottles first.

Download free files

  • Dosing rack

    Three bottle pockets and three syringe holders, labelled GROW, BLOOM and TOP-MAX

Holds
3 bottles
Footprint
205 × 99 mm
Height
62 mm

Print settings

  • Use PETG or ASA. Nutrients are mildly acidic, and PLA softens in a warm room.
  • Starting settings, not a validated profile: 0.4 mm nozzle, 0.20 mm layers, 3 walls and 15% infill.
  • Print as modelled, with the flat base on the bed. No supports needed.
  • Measure your bottles at their widest point and your syringe barrels before printing. Change BOTTLE_D, SYRINGE_D and LABELS in the generator, which is in the ZIP.
  • The ZIP includes an editable STEP file and the generator. Get print time and filament use from your slicer.

How to use

  1. Buy one 10 or 20 mL syringe per nutrient (oral or lab syringes, no needle). Mark each with the product name.
  2. Stand each bottle in its pocket and rest its syringe tip-down in the matching holder. The hole has a solid floor that catches drips.
  3. Enter the water volume and each product’s ml per litre from the label in the calculator below. It shows how much to draw and how many fills.
  4. Draw the dose with the tip free of air and read the mark at eye level. Add the nutrients to the water, never the other way round, and stir.
  5. Rinse each syringe in plain water after use and let it dry tip-down in its holder.

Dose calculator

Enter the dose from your nutrient label in ml per litre. This only multiplies it out; follow the label for the amounts.

Grow–
Bloom–
Top-Max–

Add nutrients to the water, never the other way round, and stir. Read the syringe at eye level with the tip free of air.

Untested prototype: digital checks confirm a closed, connected mesh, not the fit with your bottles or syringes. Syringes are not included. The calculator only multiplies the label dose; always follow the nutrient label.

Training

Shaping plants and tent canopies

Garden Tie Anchors for Fabric Pots

Broad, toothless rim clips that give soft garden ties an attachment point. Made for TPU for AMS, with rounded edges and recessed Nordlys lettering. Prototype: print one to check the fit.

Download free files

  • 2 mm gap anchor

    Smallest nominal rim gap; measure your seam first

  • 4 mm gap anchor

    Middle nominal rim gap, with the same broad contact surface

  • 6 mm gap anchor

    Largest nominal rim gap for a thicker seam

Material
TPU for AMS
Rim gaps
2 / 4 / 6 mm
Tie slot
12 × 4 mm

Print settings

  • Starting settings, not a validated profile: 0.4 mm nozzle, 0.20 mm layers, 4 walls, 5 top/bottom layers and 25% infill.
  • Use the Bambu TPU for AMS preset and follow its drying guidance. Print in a single colour; the lettering is recessed.
  • Keep the supplied STL orientation, with one narrow side flat on the bed. The upright 3D preview shows the use orientation.
  • Start without supports. Inspect the short bridge over the tie slot in your slicer; add a 3 mm brim if needed for adhesion.
  • Print one candidate first. The ZIP includes editable STEP solids, the generator and a fit-check guide. Get print time and filament use from your slicer.

How to use

  1. Measure the fabric rim seam and choose a gap that fits snugly without forcing it. These clips do not lock and may slip on thin, unhemmed fabric.
  2. Remove any brim and smooth rough edges. Slide the clip over the rim with the longer, branded leg outside the pot.
  3. Thread a soft garden tie through the lower slot. Keep the printed anchor on the pot, away from stems.
  4. Try a gentle pull in the intended direction. Stop if the clip slips, twists or marks the fabric. Never lift a pot by an anchor.
  5. Recheck after watering and after 24 hours under a light load. Inspect for loosening, fabric wear and cracks; leave room for growth in plant ties.
Untested prototype: digital checks confirm closed, connected meshes, not grip or durability. No physical print, load or long-term fabric-wear test has been completed. Test one on your own pot before making a set.

LST Pole Clips & Trellis Grid

Snap-on clips for the round poles of a grow tent, plus string clips that hold the cross strings, so you can build a complete trellis grid for low-stress training. A four-pole grid takes 8 pole clips and about 20 string clips. Prototype: print one of each to check the fit.

Download free files

  • 16 mm pole clip

    For 16 mm tent poles (Spider Farmer 1680D tents)

  • 22 mm pole clip

    For 22 mm tent poles (e.g. Spider Farmer Master Series)

  • Plate of 8 × 16 mm clips

    The 8 pole clips for a four-pole grid, about 25 g of filament

  • String clip

    Grips a perimeter string and carries a cross string

  • Plate of 20 string clips

    Enough for squares of 8–10 cm in a 120 × 100 cm tent

Material
PETG / ASA
Pole sizes
16 / 22 mm
Four-pole grid
8 + ~20 clips

Print settings

  • Use PETG or ASA. PLA cracks when the arms flex and softens in a warm tent.
  • Starting settings, not a validated profile: 0.4 mm nozzle, 0.20 mm layers, 4 or more walls and 100% infill if possible.
  • Print flat as supplied, with the ring on the bed, so the layers run around the ring and the arms stay strong.
  • Print one clip first. If it is loose, set CLEARANCE to 0.1 in the generator; if it is tight, use 0.3 or 0.4.
  • The ZIP includes editable STEP files, the generator and the plate script.

How to use

  1. Measure your tent pole first: sizes vary by model. Snap two pole clips on each pole, 8 in all for four poles: one for the string along the width and one a little higher for the string along the depth. Keep them 15–20 cm above the pot rims and away from the lamp’s heat.
  2. Run one string between each pair of clips to make a rectangle, and tie each end in the 4 mm hole with a double overhand knot. Use soft twine that does not stretch much, and pull it tight.
  3. Snap a string clip onto each perimeter string every 8–10 cm: press the string into the channel on top.
  4. Run a cross string between the string clips on opposite sides, pressing it into the channel underneath. Do the same from the other two sides for the second direction.
  5. Finish with a taut-line hitch on the last pole clip, so you can retighten as the plants grow, and check again after the first week.
Untested prototype: digital checks confirm closed, connected meshes, not grip or durability. These clips are not load-rated, so do not hang lights, fans or filters from them.